Request a Quote
Tell us what you need, and our team will get back to you.
Please enter your name.
Please describe your requirements.
6063-T5 vs 6063-T6 Aluminum Extrusion: Which Temper Should You Choose?
Industry Knowledge

6063-T5 vs 6063-T6 Aluminum Extrusion: Which Temper Should You Choose?

2026-10-15

Quick Answer
·6063-T5 and 6063-T6 use the same 6063 aluminum alloy chemistry. The main difference is the heat treatment process after extrusion, which affects mechanical performance.
·For most architectural aluminum profiles, 6063-T5 is the commonly selected temper because it provides a balanced combination of strength, surface finish, dimensional stability and cost efficiency.
·6063-T6 offers higher strength and is usually selected for applications where higher load capacity is required. However, stronger does not always mean better. The right temper depends on profile design, wall thickness, application requirements and project specifications.
·For OEM aluminum extrusion projects, choosing the correct temper at the beginning helps avoid unnecessary cost and performance issues.

6063-T5 vs 6063-T6 aluminum extrusion aluminum temper selection.png


What Is the Difference Between 6063-T5 and 6063-T6 Aluminum?
6063 is a magnesium-silicon (Mg-Si) alloy in the 6xxx series, and a widely used extrusion alloy worldwide. It is popular because it extrudes smoothly, holds tight tolerances, takes a clean finish and offers moderate strength.
The letters and numbers after the alloy are the *temper* — they tell the mill how the profile is treated after it leaves the die:
•    What does 6063-T5 mean? —T5 is the standard temper for architectural extrusion. After cooling from the press, the profile is artificially aged to reach a good balance of strength, surface quality, straightness and cost. It is the default for high-volume window, door, curtain wall and outdoor profiles.
•    What does 6063-T6 mean?— T6 adds a solution heat-treatment and quench step before aging, which lifts tensile and yield strength. It is chosen when a profile must carry more load, or when a thicker section still has to meet a higher strength requirement.


6063-T5 vs 6063-T6: Key Differences
•Strength
T6 generally provides higher tensile and yield strength, making it suitable for applications requiring higher load-bearing performance.
T5 can deliver adequate strength for many architectural applications where profile design and section geometry already meet structural requirements.
•Manufacturing and Fabrication
Both T5 and T6 aluminum profiles can be cut, machined, anodized and powder coated.
T5 is commonly preferred for high-volume architectural profiles because it offers good production efficiency and stable processing performance.
T6 requires tighter process control, especially for quenching and handling, to maintain dimensional accuracy and quality.
•Cost
T6 usually has higher processing requirements, which can increase production cost.
For many projects, T5 provides the required performance with better cost efficiency.

T5 vs T6 Heat Treatment.png


Which One Is Stronger — 6063-T5 or 6063-T6?
6063-T6 is stronger. It generally delivers higher tensile and yield strength, which is why it is used where the section itself carries load.
But strength is only part of the decision. The real-world performance of a profile also depends on profile geometry, wall thickness, structural design, and how the profile is fabricated and installed. A well-designed T5 section can outperform a poorly designed T6 one — what matters is whether the temper matches the job.

What it means for your project 6063-T5 6063-T6
Strength Moderate — enough for many architectural profiles Higher — for load-bearing use
Surface finish Excellent, easy to anodize Good, but needs tighter process control
Forming and fabrication Easy to bend, cut and machine Harder, more tool wear
Cost Lower Higher (extra heat treatment)
Typical use Windows, doors, curtain walls, pergolas     Industrial frames, large-span structures

A quick note: stronger is not automatically better
A common mistake is choosing T6 simply because it is stronger. On thin-wall profiles, T6 can work against you — the extra heat treatment raises quench stress and can make surface finishing more difficult, with no real benefit to the application. Base the decision on load requirement and wall thickness, not on the highest number in a brochure.


Does 6063-T6 Cost More Than 6063-T5?
Yes. T6 usually carries a higher unit cost, because the extra solution heat-treatment, the quench step and the added quality control all take more time and energy.
For many projects, T5 already delivers the performance the specification asks for, at a lower cost. T6 is worth the premium when the application genuinely needs higher strength, when the section is thick enough for T6 to make a real difference, or when the project specification names T6 directly.


How Does Temper Choice Affect Finish and Fabrication?
Both T5 and T6 profiles can be cut, machined, anodized, powder coated and wood-grain finished. The available surface treatments are the same — what changes is how demanding the processing is.
•    Finish: T5 tends to hold a smoother surface straight from the press. T6 needs tighter control to avoid distortion and finishing marks.
•    Fabrication: T6 is harder, so cutting tools wear a little faster. T5 is more forgiving for secondary operations such as bending, swaging or light forming.
•    Appearance: after anodizing or powder coating, both can reach a high-quality architectural finish, provided the temper and the process are matched.


Which Temper Should You Choose for Your Project?
Work through four quick questions:
1.    Is the profile load-bearing? Structurally critical — lean toward T6. Non-structural or decorative — T5.
2.    How thick is the wall? As sections get thicker, T6 starts to pay off in load-bearing use.
3.    How will it be fabricated? Heavy welding or post-forming can shift the answer either way — confirm with your supplier.
4.    What does the project specification say? Follow the named standard and the drawing.

How to Choose the Right Temper.png


Quick recommendation by project type

Project type Recommended temper Why
Windows and doors T5 Cost-effective, good surface, sufficient strength
Curtain wall and façade T5(T6 for very tall or special cases)  Strength driven by section geometry
Residential pergola T5 Standard spans, light load, balanced cost
Commercial or large-span pergola T5/T6 Higher load-bearing, larger sections
Shading systems (louvers, ZIP screens) T5 Good finish, easy fabrication
Heavy industrial frames and platforms T6 Higher yield strength for load capacity
Structural profiles welded into assemblies T6 Better post-weld strength retention
Decorative trim, non-load profiles T5 Lowest cost, easiest to finish

Where Are 6063-T5 and 6063-T6 Profiles Commonly Used?
Typical uses of 6063-T5
•    Window and door frames
•    Curtain wall and façade profiles
•    Residential pergola frames and louvered structures
•    Shading systems (louvers, ZIP screens, retractable roofs)
•    Decorative trim and partition profiles
•    Standard rails, frames and light enclosures
Typical uses of 6063-T6
•    Heavy industrial frames and machine bases
•    Structural components for transportation equipment
•    Commercial and large-span pergolas
•    Heavy-duty outdoor structures and shade frames
•    LED housings, heat sinks and other strength-critical parts
•    Platforms, ladders and bridge decking

6063 T5 & T6 Applications.png


Why Choosing the Right Temper Matters for Buyers
A common misunderstanding is that T6 is always the better choice because it has higher strength.
In reality, the best choice depends on the actual application. Over-specifying T6 may increase cost without providing additional value, while selecting an unsuitable temper may create performance risks.
A professional aluminum extrusion supplier should help evaluate:
•   Profile design
•   Application requirements
•   Required mechanical performance
•   Surface finish
•   Production feasibility


What Should You Prepare Before Requesting a Quotation?
To get an accurate quotation and avoid back-and-forth, prepare the following:
•    Profile drawing (PDF or CAD), or a reference sample with key dimensions
•    Alloy and temper requirement (for example, 6063-T5)
•    Application and environment (window, curtain wall, pergola, industrial, coastal)
•    Required surface finish (anodizing, powder coating, wood grain)
•    Wall thickness and any minimum mechanical requirement
•    Estimated order quantity and target delivery country
•    Applicable standard or project specification
Supplying these up front helps the supplier confirm feasibility and quote correctly the first time.


FAQ
Q1. What is the main difference between 6063-T5 and 6063-T6 aluminum? 
The difference lies in post-extrusion heat treatment, while the base aluminum alloy remains the same. T5 is cooled after extrusion then artificially aged. T6 undergoes solution heat treatment, quenching followed by artificial aging, which typically results in higher strength.


Q2. Is 6063-T6 always better than 6063-T5? 
No. The optimal selection depends largely on project application. T6 features higher strength, yet for a wide range of architectural profiles, T5 can meet performance requirements with lower cost and simpler surface finishing.


Q3. Which temper is more common for architectural aluminum profiles? 
6063-T5 is widely adopted for window, door, curtain wall and standard façade profiles in most architectural projects.


Q4. Should I choose T5 or T6 for an aluminum pergola or outdoor structure? 
The selection is determined by span, load conditions and structural design. Residential pergola frames are typically specified as T5. Commercial or long-span structures may adopt T6 when section size and loading conditions demand higher mechanical performance.


Q5. Does T6 increase the cost?
Yes. T6 involves additional heat-treatment and process control, which raises the unit cost. The exact difference depends on profile complexity and order size.


Q6. Can 6063-T5 be changed to 6063-T6 after extrusion?
Re-tempering a finished profile requires a full heat-treatment cycle and is rarely practical or economic. The temper is normally decided before production starts.


Q7. What information should I provide when requesting a quotation?
A profile drawing, application details, temper requirement, surface finish, wall thickness, quantity and target market. The more complete the brief, the faster and more accurate the quotation.


Q8. How can a manufacturer help me choose the right temper?
A qualified extrusion supplier reviews the profile design, load requirement and production feasibility, then recommends the temper that fits — rather than the one that simply sounds strongest.

In-house Aluminum ManufacturingYaoxing Aluminum.png


About YAOXING ALUMINUM
As an aluminum extrusion manufacturer, YAOXING ALUMINUM helps OEM partners and importers choose the right 6063 temper for their profile, application and market.
What we offer in-house:
•    Aluminum extrusion — custom profiles for architectural, industrial and outdoor use
•    CNC machining and fabrication — precision milling, drilling and assembly-ready delivery
•    Surface finishing — anodizing, powder coating and wood-grain transfer
•    Temper control — aging and quench capability for both T5 and T6 routes
Because extrusion, machining, finishing and fabrication sit under one roof, we can support a project from profile design through to the finished aluminum profile, with fewer hand-offs and more consistent quality.


Need Help Choosing the Right 6063 Temper?
Send us your profile drawing and application details. Our engineering team will review the design and recommend the temper that fits your project — T5 or T6 — together with a technical quotation.
Where engineering review allows, we can:
• Recommend the suitable temper — T5 vs T6, based on your profile design and application 
• Pre-check extrusion feasibility — section complexity and surface-treatment options 
To get started, send your profile drawing (PDF or CAD), application details, required finish, wall thickness, estimated volume and target country.

Send Profile Drawing Contact Our Engineering Team